I cast some .310 round balls for my .32 caliber rifle. Those things are tiny compared to the .490 and the 500 grain minieballs. Got around 300 usable balls using hardly any lead. Used a magnifying glass to pick out the usable ones from the bad.
Nice work. The .32 caliber RB are small little things for sure. Definitely economical as well. But for this ole boy, they are a bit cumbersome to load in the woods. My old numb and bumbling fingers just ain't what they use to be. Other than being somewhat difficult to deal with, in terms of loading, I really like my little .32 Crockett Squirrel Rifle.I cast some .310 round balls for my .32 caliber rifle. Those things are tiny compared to the .490 and the 500 grain minieballs. Got around 300 usable balls using hardly any lead. Used a magnifying glass to pick out the usable ones from the bad.
I too have trouble handling the .32 caliber balls. I found that using a loading block really helps at the range and in the hunting field.Nice work. The .32 caliber RB are small little things for sure. Definitely economical as well. But for this ole boy, they are a bit cumbersome to load in the woods. My old numb and bumbling fingers just ain't what they use to be. Other than being somewhat difficult to deal with, in terms of loading, I really like my little .32 Crockett Squirrel Rifle.
I too use a loading block. Much easier.I too have trouble handling the .32 caliber balls. I found that using a loading block really helps at the range and in the hunting field.
Could of gone that route but I enjoy doing things myself.
Never used a loading block and I do not understand how you can center the hole in the board directly over the board. I have given this some thought and I was going to make one, but it would not be like a speed loader with the plastic ends that opens up.I too have trouble handling the .32 caliber balls. I found that using a loading block really helps at the range and in the hunting field.
You could always have a counterbore on one side of the board that fits over the muzzle of your barrel to center the hole with the ball in it directly over the bore.Never used a loading block and I do not understand how you can center the hole in the board directly over the board. I have given this some thought and I was going to make one, but it would not be like a speed loader with the plastic ends that opens up.
You could always have a counterbore on one side of the board that fits over the muzzle of your barrel to center the hole with the ball in it directly over the bore.
That's what i do. The patched ball is pushed thru the hole so it sticks out on the back side. Place that proud patched ball in the muzzle, and use your short starter to send it home.That's a good idea. That never would have crossed my mind. Especially with the size board needed to have more than a few extra shots ready. But in a larger caliber gun I can see that where you might only need a few more shots.
I *assumed* you set the ball a bit proud on the one side to aid in punching it home.
But honestly, I've never seen one in use.
That's what i do. The patched ball is pushed thru the hole so it sticks out on the back side. Place that proud patched ball in the muzzle, and use your short starter to send it home.
I don’t use one any more, but I cut the hole a wee bit larger then the ball size so it was tight enough to hold, but loose enough I could push it through. Let a bit of the ball stick through and it could fit into the bore ‘automatically’ so no trouble to line upAnd bob's your uncle
So how do you do that?
Do you have a punch/short starter set up to only tap the ball so far through the block?
Or maybe set the block on a thin piece of rubber and use a regular short starter until it bottoms out?
I don’t use one any more, but I cut the hole a wee bit larger then the ball size so it was tight enough to hold, but loose enough I could push it through. Let a bit of the ball stick through and it could fit into the bore ‘automatically’ so no trouble to line up
Push the balls through the board until it sticks out a little bit the just put it in the barrel end and shove it on throughNever used a loading block and I do not understand how you can center the hole in the board directly over the board. I have given this some thought and I was going to make one, but it would not be like a speed loader with the plastic ends that opens up.
Same here when casting 500 grain minieballs for my Pedersoli 1861 Springfield. 14 minieballs per pound. Compared to 155 per lb of the .310's or 40 for the .490's. Really save the money casting the minieballs about a dollar apiece for them store bought.Had the opposite reaction. Ran me some .735s, first time with this size, ran a few and thought why’s my pot empty????
Enter your email address to join: