• This community needs YOUR help today. We rely 100% on Supporting Memberships to fund our efforts. With the ever increasing fees of everything, we need help. We need more Supporting Members, today. Please invest back into this community. I will ship a few decals too in addition to all the account perks you get.



    Sign up here: https://www.muzzleloadingforum.com/account/upgrades
  • Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
ZUG
Reaction score
1,637

Latest activity Postings About

    • ZUG
      ZUG reacted to hawkenhunter50's post in the thread Sidelock hammer screw. with Love Love.
      Nice attitude, I'm sure you'll get a lot of help, By the way I've never had any issues with TC screws. Not sure why the end of the screw...
    • ZUG
      ZUG reacted to poinlaw's post in the thread Ruger old army loads with Love Love.
      Buy a $20 dial caliper and measure the cast balls. Buy a set of pin gauges from McMastet-Carr sized from .452 to .457 and find out what...
    • ZUG
      ZUG reacted to Rifleman1776's post in the thread Ruger old army loads with Like Like.
      My question also. A previous owner might have messed with the cylinders. Is your lead soft? It should be. Regardless, the balls still...
    • ZUG
      ZUG replied to the thread I found 5 of Dad's C&B Revolvers....
      They are all very nice revolvers dad left you - lucky man!;). As others have said get yourself a GOOD set of gunsmithing screwdrivers, a...
    • ZUG
      ZUG replied to the thread Remington 1858/Pietta.
      They are good - You can get a gun that has a great action or you could end up with a rough one - it's a manure shoot. I have two Piettas...
    • ZUG
      ZUG reacted to Pete G's post in the thread Sidelock hammer screw. with Like Like.
      If you don’t take the hammer off then why are you messing with the screw?
    • ZUG
      ZUG replied to the thread Pietta Spiller & Burr Revolver.
      No - the springs that I ordered are factory replacements - not reduced power springs. I can alter them as I wish to get the tension that...
    • ZUG
      ZUG replied to the thread Acra glas solvent/thinner.
      Caution must be used when thinning epoxies - too much thinning down and the epoxy will not cure and end up "gummy". Do some...
    • ZUG
      ZUG reacted to CaptainVane's post in the thread Wire bolt/trigger spring with Love Love.
      The real Sherman would destroy every bear food source for 100 miles, toreup all the bear trails, killed its offspring, and told that...
    • ZUG
      ZUG replied to the thread Pietta Spiller & Burr Revolver.
      Great picture Ernbar. My barrel and frame are flush with each other. Very little clearance (0.002" - 0.003") between barrel and inside...
    • ZUG
      ZUG replied to the thread Revolver loading stand.
      One is for seating the caps if necessary and the other is a spatula for applying the lube /grease over the ball after you ram it into...
    • ZUG
      ZUG replied to the thread Revolver loading stand.
      Here it is finished except for a coat of stain and sealer or paint which my buddy will be in charge of.;)
      • P1030898.JPG
      • P1030899.JPG
      • P1030901.JPG
    • ZUG
      ZUG replied to the thread Revolver loading stand.
      The one on the right does have leather at all contact points of the Walker- barrel, recoil shield, and at the grip area. The hammer...
    • ZUG
      ZUG replied to the thread Revolver loading stand.
      Sorry for the double pictures of the same item - I don't know how to get rid of one of them.:dunno:
    • ZUG
      ZUG posted the thread Revolver loading stand in The Craftsman.
      I'm in the process making my buddy a loading stand for his new Walker clone revolver. I fashioned it after my revolver stand for my...
      • P1030897.JPG
  • Loading…
  • Loading…
Back
Top