Search results

Help Support Muzzle Loading Forum:

  1. L

    Rehardening my frizzen

    FlinterNick said: "There’s more than one way to harden a frizzen, I generally just hit with a propane torch and dip it in Track’s Surface Hardening Compound, their instructions says to quench in water, I’ve tried both water and oil, the water works better with a propane torch, oil works better...
  2. L

    Rehardening my frizzen

    Check and see how a file cuts the face. If truly as hard as it should be, a file should just barely scratch it, if not at all. If the file easily cuts it, it needs to be re-hardened. If it is original as you believe, it may have been forged of soft or wrought iron, and pack hardened ( deeply...
  3. L

    Sliding patch box latch

    For the short amount of needed travel in wood PB lid springs, heat treating is an absolute waste of energy and time. There is plenty enough natural spring inherent in all steels to work as a short range latch spring. The amount of resistance to flex is dependent on thickness rather than heat treat.
  4. L

    TOTW Tomahawks

    4140 steel is a chrome molybdenum steel widely used in modern cartridge rifle barrels. Although there are better steels for axes, it does well enough when heat treated for light to medium work. It is not so good for knife blades, as it just will not hold an edge as long most folks would like...
  5. L

    wooden patchbox spring

    I don't know about originals, but I have seen a few modern builds done that way. No one can tell from the outside.
  6. L

    wooden patchbox spring

    I have always made my latch springs in two pieces, silver brazed with silvaloy 355. May not be the original method, but I get it the way I want it to be and work.
  7. L

    wooden patchbox spring

    His thumb piece is not angled to match the lid.
  8. L

    Hardening and Tempering 4140 Steel from Rifle Shoppe

    There is not enough carbon in motor oil to even notice as far case hardening. As Dave said. ATF or canola. With 4140, any cooking oil should work. 4140 does not require a super fast cooling quench, but heat whatever oil you use to around 120/130 F. The warmed oil will produce a lesser vapor...
  9. L

    wooden patchbox spring

    I would cut the excess shaft to the right length and angle, then brass or silver braze a separate thumb piece on. That is how I make all mine anyway.
  10. L

    Anyone else ever deal with this problem?

    How does that lead lap a bore?
  11. L

    Scalping knives

    Here is an example of the above. I don't remember where I got these pics, but thank you whoever posted them originally.
  12. L

    Priming Powder

    Perceived speed of ignition may seem the same, however it has been scientifically proven that ffffg burns faster than fffg. Many believe that fffg is slower to draw moisture than ffffg, and that could be advantageous when hunting in fowl weather.
  13. L

    Brass tacks

    Unless there has been a very recent change, those brass tacks from Crazy Crow have solid brass heads, but steel shanks. Just to know, for the super PC folks, the original brass tacks had a slightly lower dome than what you will find today offered by Crazy Crow and others. Just a few years ago...
  14. L

    Testing a lock

    Beware. It is not uncommon for some locks to allow the frizzen to bounce back, and it happens to fast to see it. Put a smear of lip stick under the tail, snap the lock, and look for lip stick on the spring. The cure, if that is what is happening, is to remove some metal under the tail to allow...
  15. L

    Center-seam knife sheath

    A center seam pattern is first made as a side seam, and sewn as a side seam, although lacking a welt. Then is well wetted and twisted to a center seam. That is the easy way, but there are other methods, some using a butt joint with a special stitch and a curved needle. Articifer could better...
  16. L

    Scalping knives

    Yes. I too had to over come that feeling, but if you want PC accuracy, yours and mine are most likely over finished anyway. The over sized grip on the English is thought by many to be a one size fits all in a particular grouping such as scalpers. It used to be a given that the noticeable slot...
  17. L

    I'm Too Fat on Bowie Knives

    Here is an exact copy of the famous MUSSO BOWIE knife, now owned by Phil Collins. I made the knife to within .010/.012 of the specs on the blue print made by Joe Musso himself. Hope you enjoy a look. Blade is 01 steel, 13 3/4" long, 7/32" thick that tapers to 3/16". About 2 1/2"/2 5/8" at...
  18. L

    Scalping knives

    English grips were wider than the tangs about 1/8 or so, on the bottom side. The pin holes, 3 for English, about 1/16 dia. were offset from center so they were centered in line on the wood grip. The French grips were fitted to or close to the tangs with 2 pins of about 1/8. Latest whole French...
  19. L

    Center-seam knife sheath

    Note also. The knife being used has a clipped point. If not for the period, some would call it a Bowie knife, not knowing that clipped points go a long way back in history.
  20. L

    Center-seam knife sheath

    Just a suggestion. If you would use a common saddle stitch, the seam can be flattened and give protection to the thread. This is an old, old tute, but other than doing them with back seams, that is still pretty much how I do mine. (1) MAKING A CENTER SEAM SHEATH - PaleoPlanet...
Top