Have you tried a 1/4-28 thread ? As sloppy as it sounds you could tell evan with a hardware screw bolt of the same thread. it will tell you if it will tighten up. You only have a minor difference in thread pitch of 1/4 (.250 )x 28 TPI and 6 mm ( .236'' ) x 1 (24,5 . TPI) Over the few thread that are used the difference would hardly be notice in the pitch with a difference of .006'' per side . The tap tolerance of a 6mm tap thread is over .003'' to start with on a H3 ( tap is +.003 tolerance ) cutting tap as standard that is commonly used . I have had nipples blow out and take my hat off ( Why I shoot flints ) . Honesty I would fix the problem right. I would buy a tap 1/4 x 28 H1 ( microammeter tolerance ) tap ( McMaster-Carr) and chase retread it to a new size and buy a new quality nipple if you shoot it a lot , Safety first always, Cheers my friend , remember at 300 psi plastic burns away.
-
This community needs YOUR help today. We rely 100% on Supporting Memberships to fund our efforts. With the ever increasing fees of everything, we need help. We need more Supporting Members, today. Please invest back into this community. I will ship a few decals too in addition to all the account perks you get.
Sign up here: https://www.muzzleloadingforum.com/account/upgrades -
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Crockett rifle leakage around nipple
- Thread starter ETipp
- Start date
Help Support Muzzleloading Forum:
- Joined
- May 28, 2022
- Messages
- 9,090
- Reaction score
- 21,941
- Location
- Louisiana & My camp in Mississippi
Agree, at least drill and tap to a larger size.
rafterob
62 Cal.
Sorry, same design issue as with the CVA guns.
- Joined
- Mar 1, 2022
- Messages
- 882
- Reaction score
- 1,038
Sounds like a bad tap setup on the production line. I would not consider any fix that involves tape or some kind of sealer. Just retread for a 1/4 28 nipple. That would also take care of your loose caps. Make sure the new thread cleans up good. If it doesn't get a new drum. Traditions and CVA used to be the same company and I suspect they still use the same manufacturer so the probelms would be similar.
I recently went through the issue of a nipple being loose in the nipple seat. A 1/4-28 nipple was blown out. A replacement nipple would not tighten. Thanks for safety glasses. The fix I chose was the 7mm-1.00 nipple sold by Track of the Wolf. The new nipple works fine.
That's odd. I'm used to nipples on drums leaking (a flat surface seated on a round) but not on a bolster or snail. I've used 1/4" Teflon Tape but not on my Crockett. The nipple comes right out but can be a booger to clean off even with a wire brush. Any kind of grease usually just gets "blown" out.
I thought I read in another thread that TOW has them with prouder threads.
According to David at the Gun Works here in Springfield, Oregon, the AMPCO nipples (by TRESO) aren't as "Sloppy" as the others and fit tighter.
https://www.jedediah-starr.com/closeup.asp?cid=76&pid=863
Good Luck!
Walt
I thought I read in another thread that TOW has them with prouder threads.
According to David at the Gun Works here in Springfield, Oregon, the AMPCO nipples (by TRESO) aren't as "Sloppy" as the others and fit tighter.
https://www.jedediah-starr.com/closeup.asp?cid=76&pid=863
Good Luck!
Walt
I understand. I might be better off if my Crockett rifle had a drum, like some CVA's.
Thanks. You said it well when you stated "sloppy threads". The nipple does tighten down well, but I have noticed where the base of the nipple seats appears to be dished out as well. And, of course, the threads are deep and in good condition, but are sloppy loose.
Yes sir, as I have stated, TOTW does, in fact, sell a 7-1 repair type nipple for European ML. And, as I have previously stated, at this point I'm not sure what to do. Wait for a while until the situation becomes worse, or just order the 7-1 repair nipple and roll the dice. I guess I have it in my mind that the 7-1 might be the last chance to rectify this issue. And if something goes wrong there, then I might be screwed.
Was it difficult to retap the threads on your ML?
No drum on the Crockett rifle. So this gives me pause.
- Joined
- May 28, 2022
- Messages
- 9,090
- Reaction score
- 21,941
- Location
- Louisiana & My camp in Mississippi
I’d be leery of re-tapping existing threads. From a strength standpoint it’s better to tap into new steel. But their method may work, I’m just not familiar with it.
- Joined
- Mar 1, 2022
- Messages
- 882
- Reaction score
- 1,038
Looked at a picture of Crockett Rifle. It has a snail so I would tap it larger. In this instance there is no excuse for a loose thread. I would be talking to the dealer
It was not difficult to tap new threads in my muzzleloader. You start by drilling the tap diameter hole. The tap is installed in the tap handle and tap cutting lubricant is placed on the tap. The lead of the tap is tapered to align the tap with the hole. Cut a half turn then back up to clear the cuttings from the tap and make another turn with the handle. In the drum you may need two taps. First the tapered tap to start cutting the threads and a blunt plug tap to complete threading the nipple seat. Clear the cuttings from the nipple seat and install the new nipple.
Forcing in the series of oversized nipples to cut lager threads is mentioned in the Dixie catalog and in the Track Catalog. The oversized nipples are in the 28 thread pitch that does not match the metric threads in the CVA/Traditions nipples. In my experience this will compromise the threads and is not the best repair for stripped or loose threads.
- Joined
- Mar 1, 2022
- Messages
- 882
- Reaction score
- 1,038
I agree
Just cut a proper size thread
Just cut a proper size thread
Dave Dworshak
40 Cal
Get a new drum from TOTW. Its not worth getting hurt using a bad sealing nipple. Had myself a nipple fly by my head.
- Joined
- Mar 1, 2022
- Messages
- 882
- Reaction score
- 1,038
It doesn't have a drum.
A brass flash cup from TOTW. I use them on all of my TCs and GM barrels and there's no leak
and it keeps the area clean. Brass is soft and will form when tightened.
and it keeps the area clean. Brass is soft and will form when tightened.
- Joined
- Mar 1, 2022
- Messages
- 882
- Reaction score
- 1,038
If the thread is loose there would be a good chance of stripping it while tightening enough to seal it
Thanks. I have drilled and tapped a fair amount, but never for a ML nipple hole. The 28 thread pitch that might not be compatible concerns me. So far, I am not sure if there's enough difference between a 6-1 and a 7-1 nipple to make me want to try to drill first. But there may be. Forcing a repair tap into the hole may work okay, but it gives me pause.
