- Joined
- May 28, 2022
- Messages
- 9,093
- Reaction score
- 21,945
- Location
- Louisiana & My camp in Mississippi
Very Nice!
-
This community needs YOUR help today. We rely 100% on Supporting Memberships to fund our efforts. With the ever increasing fees of everything, we need help. We need more Supporting Members, today. Please invest back into this community. I will ship a few decals too in addition to all the account perks you get.
Sign up here: https://www.muzzleloadingforum.com/account/upgrades -
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Removing the barrel on a hooked breech rifle for cleaning, yes or no??
- Thread starter MedicMike3762
- Start date
Help Support Muzzleloading Forum:
why would you not remove it? thats its purpose. i mark my wedges on top so they go in the same as they came out.
Take it off.
Bottom part of the barrel that's in stock needs cleaned too. All of that smoke can/does have contamination in it and as it drifts through the air who is to say some doesn't get in the barrel channel?? My barrels aren't that tight fitting. From what I can tell that black stuff gets everywhere.
10 seconds total to remove and replace seems pretty minimal to me.
Bottom part of the barrel that's in stock needs cleaned too. All of that smoke can/does have contamination in it and as it drifts through the air who is to say some doesn't get in the barrel channel?? My barrels aren't that tight fitting. From what I can tell that black stuff gets everywhere.
10 seconds total to remove and replace seems pretty minimal to me.
Also the lock periodically as it too gets filthy
Take it off.
Bottom part of the barrel that's in stock needs cleaned too. All of that smoke can/does have contamination in it and as it drifts through the air who is to say some doesn't get in the barrel channel?? My barrels aren't that tight fitting. From what I can tell that black stuff gets everywhere
10 seconds total to remove and replace seems pretty minimal to me.
I am a bit OCD about my guns anyway. Even my modern guns get a wipe down at the end of the day. Not much, just a little coat of oil.
Bottom part of the barrel that's in stock needs cleaned too. All of that smoke can/does have contamination in it and as it drifts through the air who is to say some doesn't get in the barrel channel?? My barrels aren't that tight fitting. From what I can tell that black stuff gets everywhere
10 seconds total to remove and replace seems pretty minimal to me.
All around snail too. Hell even my stock below the nipple is black after a range session.
I am a bit OCD about my guns anyway. Even my modern guns get a wipe down at the end of the day. Not much, just a little coat of oil.
- Joined
- Jan 9, 2008
- Messages
- 1,893
- Reaction score
- 2,092
The hooked barrels are removed from the stock, along with the locks. The breach is placed in a bucket of water and water is drawn into the barrel by my dedicated cleaning rod and some tight patches flushing out all the accumulated fouling.
Black Dog
32 Cal
I always remove hooked-breech barrels for cleaning. Because I equipped all my T/C rifles with tang-mounted peep sights, I replaced the T/C mid-sights with their "primitive" bases, installed a Marble's or Lyman folding sight adjusted to the peep-sight's zero and flipped it up to confirm the zero when I reassembled the rifle. That practice spans close to 50 years of shooting with at least a half-dozen rifles, and only once did the barrel-removal mode of cleaning require readjustment of the peep sight, and that was very minimal. (Until I got my present, as-yet-untested T/C flintlock Hawken, the peep sights were all of the T/C hunter type; since those originally $25-$30 sights now sell for an outrageous $160-$180 apiece, my flinter wears a Williams Foolproof made for the Hawken, which unlike its Lyman counterpart does not require the removal of wood from the stock.)
Erwan
45 Cal.
For me, it's mixed: I dismantle the pinned barrels only twice a year and the hooked-breech barrels around one time by two months or a bit more...
All the wood and the underside of the barrel are greased with "marine" quality grease insoluble in water...
I've always heard from the old timers that it's bad to disassemble the barrels too often because it's hard to get them back in place, it takes several shots before it settles down. For hunting, I don't know if it matters much but for target shooting, it is quite and even very sensitive...
All the wood and the underside of the barrel are greased with "marine" quality grease insoluble in water...
I've always heard from the old timers that it's bad to disassemble the barrels too often because it's hard to get them back in place, it takes several shots before it settles down. For hunting, I don't know if it matters much but for target shooting, it is quite and even very sensitive...
Yes, I remove the barrel from the stock to clean it every single time too! Don't have to be nearly as careful and protective of the stock that way!
I have noticed after reinstalling my barrel it has to be "settled in" with several shots to get back where it was so I only pull them about once or twice a year. I'm saving powder and lead!
- Joined
- Jul 24, 2018
- Messages
- 4,497
- Reaction score
- 5,613
I own 3 rifles with hooked breeches and I have fired 0 of them so far .
But when I used to own T/C's including my Big Boar in the 90's, I used to take down the barrel to clean because it's easier
But when I used to own T/C's including my Big Boar in the 90's, I used to take down the barrel to clean because it's easier
- Joined
- Mar 5, 2021
- Messages
- 251
- Reaction score
- 362
The hooked breech was designed and manufactured to aid in take down for cleaning. The fights on mine are fixed to the barrel. I have never had a problem with accuracy drifting.
It is most important to me that a thorough cleaning be done.
It is most important to me that a thorough cleaning be done.
I have always removed the barrel for cleaning with my hooked breach rifles. When initially acquired( whether kit or finished), I have made certain that the barrel/breach/recoil plate(stock) was properly fitted(no gaps at the breach), the barrel channel/fore-end tip/nose cap) was properly bedded, and, the barrel keys matched and fitted, applying minimum downward force on the barrel. Never have had an issue with POI, or accuracy changes(1-2MOA) due to barrel removal/replacement. I keep the hooked breach fitment and barrel wedges lightly lubed for minimal wear.
- Joined
- Jan 15, 2009
- Messages
- 2,688
- Reaction score
- 2,741
i sometimes remove the hooked breech barrel, not always. Decades ago, when i had good eyes there were indications that the rifle sometimes shot to a slightly different point of aim when re-assembled. The most accurate rifle i currently own in a Navy Arms .54 without the hooked breech.
Never got into cleaning the patent breech. i simply clean the flame channel with a bristled pipe cleaner. After loading the powder, the rifle is leaned lock side down and the stock is given a couple whacks with the palm.
Never got into cleaning the patent breech. i simply clean the flame channel with a bristled pipe cleaner. After loading the powder, the rifle is leaned lock side down and the stock is given a couple whacks with the palm.
vince-m
40 Cal
Done it for years, renegade shots same every time.....
- Joined
- Jun 12, 2005
- Messages
- 7,970
- Reaction score
- 964
i take my hooked barrels off to clean them (not to sound like a conformist - that's just what works best for me).
Beautiful rifle 
Morena ( good morning).
In the same camp as most of you hooked breeches are nice & easy to dissemble
I've a few pinned rifles & if wet or heavy day on the BP I usually take the bareel out as well.
If you have bang on size punches and go easy on it , it's not too tricky.
I usually if buying a pinned rifle ask if owner would mind .
It can change your mind when you see undenath.
Have a awesome day everyone. Well mostly northern hemisphere folks here. So good evening
Ma te wa ( all the best)
Chris
In the same camp as most of you hooked breeches are nice & easy to dissemble
I've a few pinned rifles & if wet or heavy day on the BP I usually take the bareel out as well.
If you have bang on size punches and go easy on it , it's not too tricky.
I usually if buying a pinned rifle ask if owner would mind .
It can change your mind when you see undenath.
Have a awesome day everyone. Well mostly northern hemisphere folks here. So good evening
Ma te wa ( all the best)
Chris
