It’s not like Colt came up with a paper cartridge loaded with a conical during the Civil War or we would have heard about it.
Do I detect some "tongue in cheek" there?
I'm sure you know that pointed bullets were commonly used in Colts revolvers?
Here's a quote from ole' Sam Colts loading instructions for his percussion revolvers:
----------------------
" DIRECTIONS FOR LOADING COLT'S PISTOLS.
First explode a cap on each nipple to clear them from oil or dust, then draw back the hammer to the half-cock, which allows the cylinder to be rotated; a charge of powder is then placed in one of the chambers, keeping the barrel up, and a ball
with the pointed end upwards without wadding or patch is put into the mouth of the chamber. turned under the rammer, and forced down with the lever below the surface of the cylinder, so that it cannot hinder its rotation
(Care should be used in ramming down the ball not to shake the powder from the chamber, thereby reducing the charge).
This is repeated until all the chambers are loaded. Percussion-caps are then placed on the nipples on the right of the lock-frame, where, by drawing back the hammer in the full-cock the arm is in condition for a discharge by pulling the trigger; A repetition of the same motion produces the like results with six shots without reloading.
It will be safe to use all the Powder the chambers will hold, when loading with the flask, leaving room for the Ball, whether the Powder is strong or weak. Fine grain Powder is the best. Soft lead must be used for the balls. The cylinder is not to be taken off when loaded. The hammer, when at full cock forms the sight by which aim is taken.
To carry the arm safely when loaded let down the hammer on one of the pins between each nipple, on the end of the cylinder.
The arm should be throughly cleaned and oiled after firing, particularly the arbor-pin on which the cylinder turns.
DIRECTIONS FOR LOADING WITH COLT'S FOIL CARTRIDGE
Take the white case off the Cartridge, by holding the bullet end and tearing it down with the black tape. Place the Cartridge in the mouth of the chamber of the cylinder,
with the pointed end of the bullet uppermost, one at a time and turn them under the rammer, forcing them down with the lever below the surface of the cylinder so that they cannot hinder its rotation.
To ensure certainty of Ignition, it is advisable to puncture the end of the Cartridge, so that a small portion of gunpowder may escape into the chamber while loading the pistol.
DIRECTIONS FOR CLEANING
Set the lock at half-cock; drive out the key that holds the barrel and cylinder to the lock-frame, then draw off the barrel and cylinder by bringing down the lever and forcing the rammer on the partition between the chambers. Take out the nipples. Wash the cylinder and barrel in warm water, dry and oil them throughly; oil freely the base pin on which the cylinder revolves.
TO TAKE THE LOCK TO PIECES, CLEAN AND OIL
First--Remove the stock, by turning out bottom and two rear screws that fasten it to guard and lock-frame, near hammer.
Second-- Loosen the screw that fastens mainspring to the trigger guard and turn spring from under tumbler of the hammer.
Third--Remove the trigger guard by turning out the three screws that fasten it to the lock-frame.
Fourth--Turn out the screw and remove the double arm spring that bears upon the trigger and bolt.
Fifth--Turn out the screw pins that hold the trigger and bolt in their places.
Sixth--Turn out the remaining screw-in and remove the hammer with hand attached, by drawing it downwards out of the lock-frame. Clean all the parts and oil them throughly.
TO PUT THEM TOGETHER--Replace the hammer with hand-spring attached, then the bolt, the trigger, the sear spring, the trigger-guard, the mainspring, and finally the handle, returning each screw to its proper place, the arm is again in for use."
-------------------------
I added the underlines to words to draw folks attention to them.
I might also note, Colt had a contract with Eley in the UK to produce foil cartridges with pointed bullets in them. The Colt company sold them in the US.
As I recall, the foil was made in Germany and to the best of my knowledge, no one today knows exactly what it was. Modern aluminum foil doesn't seem to work.
