• This community needs YOUR help today. We rely 100% on Supporting Memberships to fund our efforts. With the ever increasing fees of everything, we need help. We need more Supporting Members, today. Please invest back into this community. I will ship a few decals too in addition to all the account perks you get.



    Sign up here: https://www.muzzleloadingforum.com/account/upgrades
  • Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Recent content by Darkhorse

Shop deals on ebay
the hawken shop
Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. D

    Left handed flintlock question

    I am totally lefthanded and shoot lefthanded. I am old enough to have learned to shoot righthanded because LH rifles were almost nonexistant. But just as soon as I saved up enough dollars to buy a LH rifle that's just what I did. I now have 3 LH bolt guns. And I've built my own LH flintlocks. It...
  2. D

    How to carve Moldings

    For the straight cuts I clamp a straight edge, against the stock , then using the straight edge as a guide I run a pencil mark down it. Now I can see if it's where I want it to be. If it is I use a parting tool held against the straight edge to make a light cut the length of the straight line...
  3. D

    Slotting pin lugs

    SMO, My lugs are made of soft steel. My pins are made of drill rod. They are harder, I haven't even had one to bend yet. Before and behind the lug is a long stretch of tough maple which keeps the pin from breaking, though I'm sure eventually the pins will split out the maple. I'm sure drilling...
  4. D

    Slotting pin lugs

    SMO, The lug was bent up towards the muzzle. I don't believe the slotting caused the lug to crack. One thing I don't understand is why it took nearly 20 years to crack that lug. I don't have any thing to compare them to but you have seen photo's of some of my targets, some of my good ones how do...
  5. D

    Slotting pin lugs

    SMO....you might be wrong about this. Especially about a free floated barrel. I slot all my rifles in both directions. Never questioned it. Then a couple of years ago I had taken apart my 20 year old Lancaster .54 and happened to notice something strange looking about that first slot. Looking...
  6. D

    When to change touch hole liner?

    FWIW 20 or 30 years ago when I was building my first rifle I called Jim Chambers place of buisness and asked them about the touchhole size. This is what I was told. In the years since it has worked to perfection and I'm very picky about the performance of my lock and rifle. "When you first go...
  7. D

    Full cock in stand

    The hammer stall keeps your frizzen dry and clean, but also works as a sort of safety. It is made of stout leather and if you try to fire your flintlock with it down on the frizzen all you get is a soft "thud" when the flint hits the leather. The flint doesn't penetrate the leather so no sparks...
  8. D

    How do you waterproof a wooden ramrod

    I use jim Chambers finish on all my new guns, usually about 8 hand rubbed coats. After the last coat has thouroughly dried I use Q tips and split wood shafts with a piece of cloth held in the split. I use the Q tips soaked in finish to seal every crack and hole. Then I use the split shaft, coat...
  9. D

    Traditional gun stock finish

    Try some Jim Chambers original oil finish. It's all I use anymore and I'm pleased with the results.
  10. D

    Replace Front Sight on my Kibler

    Have you considered a simple peep sight for the rear? My eyes got to where they couldn't focus on either front or rear, I always saw multiple lines. I made a simple peep sight and that cleared both sights up. It's worth a try.
  11. D

    Kibler stocks OK for a lefty?

    "And my sympathy."
  12. D

    Trouble…

    How so? And what expensive, proper tooling do you speak of? I was going to suggest pulling the breechplug, pouring out the dry (ungreased powder) and driving the ball out the front. I've done it with no harm to my rifle. I don't know if the pederasoli can even be unbreached by the common man...
  13. D

    Colerain or Rice........?

    I have a Rice .40 and a Colerain .54, both shoot very accurately and I would buy either one again. The Rice was clearly better machined and finished while the Colerain took a good bit more time to finish up. The Rice is a nicer barrel and priced so but mine doesn't outshoot the Colerain. I like...
  14. D

    Kit stocks

    I'm pretty sure Wayne Dunlap doesn't make stocks either. At least he didn't several years ago when I was looking for a LH Isacc Haines in 50 caliber B profile. Wayne is an excellent supplier of premium wood though. And offers a better choice in his kits than most.
  15. D

    Elk Hunting

    Yeah I know, this is an old post. But it is an old post of mine, I am the OP. I ran across this by accident and decided it needed finishing. I put in for a rut hunt with muzzleloaders for years without getting drawn. That's the short answer. The long answer is I was employed by the department of...
See more
Back
Top