• This community needs YOUR help today. We rely 100% on Supporting Memberships to fund our efforts. With the ever increasing fees of everything, we need help. We need more Supporting Members, today. Please invest back into this community. I will ship a few decals too in addition to all the account perks you get.



    Sign up here: https://www.muzzleloadingforum.com/account/upgrades
  • Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Recent content by Col. Batguano

muzzle loading side side shotguns
the hawken shop
shop deals on amazon
Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. C

    bending brass for patch box cover?

    It's really quite surprising to me that you don't feel the bump from PB lid latch, or round head screws coming through the butt plate when you're shooting the gun, (like a piece of gravel in your shoe) but you just don't.
  2. C

    browning

    When doing rust blueing, in order to get best results I need to heat up the parts in a low humidity environment first. When they're warm, THEN introduce them to the high humidity session, and card afterwards. That keeps the moisture from condensing on the parts (as stated previously). Repeat...
  3. C

    browning

    When you're neutralizing, it doesn't hurt to do it a few times. Ammonia, and baking soda paste followed with a water wash are the most common ways to do it.
  4. C

    browning

    Don't be too frustrated. Unless you're hanging it in a high humidity area like a shower or steam box, in most places, this time of year the humidity in your house might be only about 20%. (It is in mine.) Just give it a little more time than it might require in the summer months.
  5. C

    bending brass for patch box cover?

    You could start with a thicker piece of brass like 1/8" and just file the curve you want in to it, removing the middle. I did that with the end piece on a domed PB lid. Much easier. With homogeneous material like brass for the lid, and brass for the end plate, it's pretty it hard to see...
  6. C

    Trigger guard install

    You should wait on doing your drilling (of the metal tabs) for pinning until just after the stock is dyed, or even finished. Those holes need to be cleaned up from varnish that gets in there after the gun is finished anyway. The reason for this is the stock dimensions are going to swell...
  7. C

    Carburetor cleaner

    The primary active ingredient in carburetor cleaner is acetone. It's cheaper by the gallon than it is by the spray can.
  8. C

    Why does the stone need a wrap?

    There always has to be something that gets in between a rock and a hard place. :rolleyes:
  9. C

    First time screwing up a dovetail

    Adjustable sights are ALL fixed sights once you stop adjusting them.
  10. C

    My first attempt at Rococo

    Wonderful work! It embodies all the critical elements. Aspiration, followed by inspiration, fueled with dedication, oiled with perspiration.
  11. C

    Where can I buy inserts' for my stock?

    With side plates you're really better off making your own. The reason being, is that every gun's architecture is slightly different in the 3 main points you're concerned with; the location / relationship of the 2 stock bolt holes, how the plate orients toward the lower fore end, and how the...
  12. C

    First handmade nose cap

    I've never done a domed rivet before. Mine have always been flush. Domed sounds a lot harder. to get good results. I would think you have to pre=shape the head to match the convex surface of the muzzle cap for one thing. If you try to bend the edges over while in place you risk denting in...
  13. C

    First handmade nose cap

    The proof in the pudding is always in how it fits. Do the top and bottom lines of the fore stock continue straight through the muzzle cap, or, do they take something of a bend at the junction? On my most recent build I wound up making 3 muzzle caps before I was satisfied with the results. Are...
  14. C

    Bore/barrel size

    Oops. You're right! My mistake. The correct numbers are; 0.08", 0.10" and 0.12" Sorry if it caused confusion.
  15. C

    Bore/barrel size

    Right you all are, but modern guns are made with modern steels. Many of out ML'ing barrels are 12L14 steel, which isn't as tough. That said, a cut-in barrel lug or sight is going to have most of that cut away steel replaced by the lug base, so much of what is lost is then replaced. If you...
See more
Back
Top