• This community needs YOUR help today. We rely 100% on Supporting Memberships to fund our efforts. With the ever increasing fees of everything, we need help. We need more Supporting Members, today. Please invest back into this community. I will ship a few decals too in addition to all the account perks you get.



    Sign up here: https://www.muzzleloadingforum.com/account/upgrades

Ready to Start.

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Mockingbird

32 Cal.
Joined
Jun 29, 2013
Messages
43
Reaction score
6
Finally getting ready to start my fist kit build. I purchased a chambers Little Feller's Rifle kit and am going to start working on it so my 11 y/o son and I can go out shooting together. I have done some horn work in the past but this is my first gun build. Got the garage re-organized and made a spot for my bench (just a start). I plan on making hangers for tools to go on the wall and I want to get a good work light as well. Here is a pic of my station so far:
Bench001.jpg
I have the bench weighed down with about 100lbs (or more) of lead ingots. and it is bracketed to the wall so it is nice and stable. The vice is mounted on 2x8 that is secured to the table with bolts through the bench dog holes. Can easily be moved back and forth if needed. Since this is my first build any suggestions on setup or tools would be greatly appreciated. For tools so far I have:
Chisels
12mm Flat (Pfiel) , 6mm Flat (Pfiel), D7/10 (Pfiel), D1/12 (Pfiel), D12/8 (Pfiel), 1/8 offset (usa), 1/4 offest (usa), 3/8 offset (usa)
Files:
I have a large smooth mill file, Needle files, Nichelson Cabinet rasp, Triangle file with and without smooth edges, Smooth and corse rat tail files.
Other:
Leather mallet, Cabinet scrapers, Various size drill bits

Things I think I need: Wood mallet, gunsmith screwdrivers (not sure on sizes), Counter sink drill bits (not sure on sizes), good hacksaw, I am sure I am missing other files.

Like I said feel free to chime in with opinions and suggestions I will update this post as I go along.
 
I'd get it off the wall before "IT" happens. You know "IT". You get going, a few weeks in, fitting the nose piece, thin wood, get careless and when you swing it around for a better look.......oops.
I prefer my bench open at both ends just in case. But that's just me.
Ames,
The bench isn't an expensive one and does need the wall for stability. Might it be better to mount it back side to the wall?
 
I know you already have a vise, but I can say the handiest tool I added this year was the Patternmakers vise. I spent a ridiculous amount of time shimming and trying to get the stock secure in a standard vise as you have. Now I just tighten and go, simple - no shimming, no worrying about protecting the wood. Saves a lot of time and headache.

https://www.woodcraft.com/products/woodriver-patternmakers-or-gunstock-carving-vise

Also, I assume Chamber's sold you a tap?
 
Also, I assume Chamber's sold you a tap?

Indeed sir. I have the tap and drill bit from Chambers.


Dave thanks for the link. I had just found your post yesterday before putting up this post. Looking at the angle of the butt plate on mine it looks much better than yours was. The rear ramrod pipe tang has the same gap on the sides as yours did which really is a bummer. I would rather have to remove the extra wood and also be able to do a design in the tang than have that pre-inlet. I haven't taken a super close look at the lock yet but the pan seems to be nice and secure. All the work you had to do to the lock is the only thing that worries me. I am really appreciative of the tutorial you did I am sure it will save me much head scratching. As this is my first build I just plan to take it slow and steady, reference the books, and come here to ask lots of questions.
 
The bench isn't an expensive one and does need the wall for stability. Might it be better to mount it back side to the wall?
Being able to work all around a bench is ideal but not always do-able. Your current setup is great but I wouldn't attach a side to a wall. Being able to move the vise, or more importantly, remove the vise altogether when desired, is excellent. Bravo. The bench appears finely crafted but too light. Ames makes the best point of all; "sharp tools."
 
You're going to probably want a second vise or at least a way to securely hold the stock so you won't have to crank down so hard to hold it. It doesn't have to be a long way away from the first. About a foot would do it, but 2 would be better. The wider and greater the gripping area of the vice jaws the better too. Much more distance between them
work shop set up 2.jpg
than that and the wood may bow a bit when you are working between the vices, particularly on thin sections, like the upper forestock.
 
Last edited:
Ames,
The bench isn't an expensive one and does need the wall for stability. Might it be better to mount it back side to the wall?
Yes, for sure! You can get rid of your weights if you fasten the bench with it mounted against the wall. You want both ends of the bench open. Nice start, but I personally like the vice on one end. You are limiting your bench space by placing it in the middle. I do a lot of stock work with it being right down on the bench.
Your son is blessed to have a dad that will make him a good rifle.
Flintlocklar
 
Back
Top